#Logicmaster 90 micro software download series#

ThereвЂ™s only 0.625A total available current on the 24VDC output of the power supply.ДonвЂ™t hesitate to contact our tech support department with any other questions regarding your GE Fanuc Series 90-30 PLC at 1-86.Your interpretation of the terms 'Upload' and 'Download' is the opposite of the way both Logicmaster and VersaPro define them. Yes, but you should be aware that using this output will reduce the amount of current available on the 24VDC output that goes to the Series 90-30 modules via the baseplate. This port is for the Ethernet Station Manager only!Д¬an I use the external 24VDC output on the Series 90-30 power supply to power external devices?

#Logicmaster 90 micro software download serial#

If your problem isnвЂ™t solved after checking all these things, call our technical support specialists at 1-86.Д¬an I program my Series 90-30 IC693 CPU364, CPU372, and CPU374 through the serial port on the CPU module? If the +5 volts is not present, the fuse for that port is blown. You can check the +5 volt pin (pin 5) on the programming port versus pin 7 (0 volts). In cases where you think the setting may be changed and you have a copy of the PLC configuration, compare the CPUвЂ™s port configuration to your softwareвЂ™s port settings. The default settings for the Series 90 CPU programming port are 19200 BAUD, 8 data bits, 1 stop bit, and odd parity. You can try connecting to another Series 90 PLC in order to confirm the condition of the cable. You can try to use the PCвЂ™s serial port to communicate to another device in order to confirm proper operation. There could be several causes of the problem. What are the possible causes of this problem? My PLC will not communicate to the programming port on my Series 90 CPU.

#Logicmaster 90 micro software download software#

Note that if the OK LED light is out, the software wonвЂ™t be able to communicate. These will help you find the root cause of your problem. If both of these are fine, then use one of the available programming packages (the three software programs mentioned above) to connect to the Series 90 programming port and check the PLC and I/O fault tables. Key ones to check are the POWER LED (which will indicate the health of your power supply) and the OK LED (which will indicate the health of your CPU).

How do I identify the cause?Д¬heck the LEDs on your power supply as well as the CPU. You should only do this when passwords arenвЂ™t a problem.

#Logicmaster 90 micro software download download#

Once the memory is erased, a configuration with вЂњPasswords EnabledвЂќ can be downloaded onto the CPU.ДЄlternatively, you could also change the configuration being downloaded to a вЂњPasswords DisabledвЂќ setting and then download the configuration onto the CPU. This is done by removing the CPU from the baseplate and shorting across two solder pads labeled вЂњMEM CLRвЂќ for about ten seconds. In some cases, you may have to clear the memory by shorting out a super-capacitor on the CPU module. You can do this by turning off the CPU, disconnecting the battery, and then turning the CPU back on with the battery still disconnected. When you disable passwords in a Series 90 CPU, thereвЂ™s only one way to download a configuration where the CPU is configured for вЂњPasswords Enabled,вЂќ and that is to completely erase the memory in the target CPU. When you try to download a configuration where the CPU is configured for вЂњPasswords EnabledвЂќ and the CPU being downloaded is set for вЂњPasswords Disabled,вЂќ you get this error. When I try to download the configuration to my Series 90 CPU, the download fails because passwords are disabled. While improvements to this software arenвЂ™t ongoing, this is the only software that will support new Series 90-30 and VersaMax CPUs and modules as they become available. This is the current software package for Series 90-30 PLCs and it supports all of the same PLCs that VersaPro Standard can as well as several of the newer Series 90-30 and VersaMax PLC that VersaPro Standard doesnвЂ™t.

#Logicmaster 90 micro software download windows#

Another Windows-based package, it can run in Windows 2000, XP, and Vista. Proficy Machine Edition Logic Developer PLC Standard Edition.VersaPro Standard can program Series 90 Micros and even certain VersaMax Micro and modular PLCs.

This Windows-based package can run in 95, 98, 2000, and XP environments, although like the Logicmaster, itвЂ™s not supported by GE Fanuc in the Windows Vista environment. As a mature product, no further improvements are planned. Please note that this software isnвЂ™t supported by GE Fanuc in Windows XP and Vista environments. As the original software for the Series 90-30 PLC, itвЂ™s DOS-based for your convenience to run in Windows 95, 98, and 2000. You have the choice of three different software packages for troubleshooting your GE 90-30. What software is available to program and troubleshoot GE Series 90-30 PLCs?

Below youвЂ™ll find some of the most frequently asked questions about the GE Fanuc line of PLCs when it comes to tech support!